工具
Ultrasonic Cutter (ULSO) 超声波橡胶切割机
| 型号 NO | 84A (40Khz) |
| 使用电力 | 800W |
| 使用电压 | 220V AC (输入电压范围 :AC 200V~230V 50Hz, 60Hz) |
| 其他 | PLL Auto_Tuning Over load check (过电流、过功率、过电压、过温度) 保持一定振幅 外观尺寸 : 宽 350mm 长 440mm 高 140mm |
Main Amp
Front-view
| 1 | power | Power supply switch to the amp |
| 2 | Red led | It indicates the alarm is on |
| 3 | Reset | It releases the alarm and reset the amp |
| 4 | Test | The ultrasonic wave is output while being pushed |
| 5 | Power[%] | It visualizes the ultrasonic output energy |
| 6.7 | It is used to control the ultrasonic amplitude | |
| 8 | It displays the status of amplitude controlling function | |
| 9 | It can access to the amplitude configuration function and control amplitude display status |
Back Side-view
| 1 | AC Main Power Connector | |
| 2 | External Amplitude Control Connector | |
| 3 | External Ultrasonic Run Signal Connector | |
| 4 | Alarm and Deposition Signal Provision Connector | |
| 5 | Ultrasonic Electric Power to Converter Connector |
Tool Horn
| 1 | Horn | Model-40HT | A blade uses the ultrasonic wave vibrated by the booster to cut the tire and the materials vary depending on the conditions |
| 2 | Booster | Model-40BA | It has a function to greatly amplify the vibration of the ultrasonic wave or decrease it and is also called main horn. A1[7075-T6511] is used to cut the tire |
| 3 | Converter | Model-40CV | Function to change the electric signal to the mechanical signal |
Patent Application
| Application Number | 30-2013-0053892 |
• Cut Signal Back Side-4, Pin #7(Black), Pin #8(White)
• Alarm Signal Back Side-4, Pin #11(Red), Pin #14(Green)
• External Amplitude Control Pin #8, Pin #1
• Start Signal Pin #2(White), Pin #6(Black)
• If you want to use the external amplitude function, turn off the S1 Dip Switch Power of the controller within the front part inside the amp and then turn on the #2 Switch
 |
Temperature and Humidity Condition | Temperature [+5˚C to +50˚C] Humidity [30% to 95% for anti-condensation] |
 |
After Service [A/S] | The amp will be repaired within 3days after we receive it
The Tool Horn will be repaired within 7days after we receive it |
 |
Warranty Period | 1year after the delivery date for the amp
3months after the delivery date for the tool horn [Converter, Booster, Horn] |
 |
Do not contact the tool Horn while it is in operation | |
 |
The power to the amp must be turned off to replace the tool Horn |
Building Drum 绿色轮胎成型鼓
Front-view
Measure-view
Air Viberator 气压多功能振动器
气压振动器
通过高频振动处理微小气泡，减少维修，增加强度。
本来由2人共同操作的工序，仅1人便可方便操作，提高工作效率。
本来由 2人共同操作的工序，仅1人便可方便操作，提高工作效率。
Basically, the work requiring two men power can be done by one person.
可减少操作工每天在操作过程中因为振动产生的手颤抖及疲劳。
本来由2人操作或者1人两次操作的工序，一次性简单完成。
本产品可通过调整气压调节振动强度，产品尺寸可定制。
Improvement Effect for Operator’s hand trembling due to daily continuous vibration work and working fatigue.
It can make easy to work which need two men’s work or two times work and can be done only one time with easy.
The vibration strength by air adjustment, product, length is diversified so that it can be adapted easily to working circumstances.
气压振动器与电力振动器比较
| 比较 | 电力振动器 | 气压振动器 |
| 操作人员 | 2人共同操作 | 1人单独操作 |
| 长度 | 5~7米 | 0.6米以上可定制 |
| 重量 | 振动棒电缆7kg，电机8~10kg | 4~5kg左右 |
| 强度调节 | 强度调节不可 若调节强度需购用高价逆变器 |
强度调节可能 |
| 便捷性 | 振动电缆、电机分别搬运 | 1人单手便捷搬运 |
| 操作者振动感应 | 振动强烈 | 接近零振动 |
| 雨天使用可否 | 雨天触电危险 | 正常使用 |
| 动力 | 220V电力 | 压缩空气，60mm, 45mm产品7马力以上 / 33mm产品3马力以上 |
| 耐久性 | 间歇性轴承老化，电线、电机老化 | 无轴承运转，结实耐用，后方排气方式对操作者身体无害 |
| 平均使用寿命 | 1~1.5个月（在pc车间连续使用时) | 3~6个月（在pc车间连续使用时) |
混凝土打磨气压振动器参数
| 区分 | SV60 | SV45 | SV33 | Remark |
| 振动棒直径 | 60mm | 45mm | 33mm | 胶管延长可能 |
| 使用压力 | 建议5.5kg/㎠7马力以上 | 建议5.5kg/㎠7马力以上 | 建议4.5kg/㎠7马力以上 | 可用压力 |
可生产长度
